Effects of dry density and grain size distribution on soil-water characteristic curves of sandy soils

The unsaturated soil mechanics is receiving increasing attention from researchers and as well as from practicing engineers. However, the requirement of sophisticated devices to measure unsaturated soil properties and time consumption have made the geotechnical engineers keep away from implication of the unsaturated soil mechanics for solving practical geotechnical problems. The application of the conventional laboratory devices with some modifications to measure unsaturated soil properties can promote the application of unsaturated soil mechanics into engineering practice. Therefore, in the present study, a conventional direct shear device was modified to measure unsaturated shear strength parameters at low suction. Specially, for the analysis of rain-induced slope failures, it is important to measure unsaturated shear strength parameters at low suction where slopes become unstable. The modified device was used to measure unsaturated shear strength of two silty soils at low suction values (0 ~ 50 kPa) that were achieved by following drying path and wetting path of soil-water characteristic curves (SWCCs) of soils. The results revealed that the internal friction angle of soil was not significantly affected by the suction and as well as the drying-wetting SWCCs of soils. The apparent cohesion of soil increased with a decreasing rate as the suction increased. Further, the apparent cohesion obtained from soil in wetting was greater than that obtained from soil in drying. Shear stress-shear displacement curves obtained from soil specimens subjected to the same net normal stress and different suction values showed a higher initial stiffness and a greater peak stress as the suction increased. In addition, it was observed that soil became more dilative with the increase of suction. A soil in wetting exhibited slightly higher peak shear stress and more contractive volume change behaviour than that of in drying at the same net normal stress and the suction.

Influence of Osmotic Suction on the Soil-Water Characteristic Curves of Compacted Expansive Clay

Unsaturated clays are subject to osmotic suction gradients in geoenvironmental engineering applications and it therefore becomes important to understand the effect of these chemical concentration gradients on soil-water characteristic curves (SWCCs). This paper brings out the influence of induced osmotic suction gradient on the wetting SWCCs of compacted clay specimens inundated with sodium chloride solutions/distilled water at vertical stress of 6.25 kPa in oedometer cells. The experimental results illustrate that variations in initial osmotic suction difference induce different magnitudes of osmotic induced consolidation and osmotic consolidation strains thereby impacting the wetting SWCCs and equilibrium water contents of identically compacted clay specimens. Osmotic suction induced by chemical concentration gradients between reservoir salt solution and soil-water can be treated as an equivalent net stress component, (p(pi)) that decreases the swelling strains of unsaturated specimens from reduction in microstructural and macrostructural swelling components. The direction of osmotic flow affects the matric SWCCs. Unsaturated specimens experiencing osmotic induced consolidation and osmotic consolidation develop lower equilibrium water content than specimens experiencing osmotic swelling during the wetting path. The findings of the study illustrate the need to incorporate the influence of osmotic suction in determination of the matric SWCCs.

Measurement systems of soil water matric potential and evaluation of soil moisture under different irrigation depths

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Hydraulic properties of layered soils influence survival of Rhodes grass (Chloris gayana Kunth.) during water stress

Survival of vegetation on soil-capped mining wastes is often impaired during dry seasons due to the limited amount of water stored in the shallow soil capping. Growth and survival of Rhodes grass (Chloris gayana) during soil drying on various layered capping sequences constructed of combinations of topsoil, subsoil, seawater-neutralised residue sand and low grade bauxite was determined in a glasshouse. The aim was to describe the survival of Rhodes grass in terms of plant and soil water relationships. The soil water characteristic curve and soil texture analysis was a good predictor of plant survival. The combination of soil with a high water holding capacity and low soil water diffusivity (e.g. subsoil with high clay contents) with soil having a high water holding capacity and high diffusivity (e.g. residue sand) gave best survival during drying down (up to 88 days without water), whereas topsoil and low grade bauxite were unsuitable (plants died within 18-39 days). Clayey soil improved plant survival by triggering a water stress response during peak evaporative water demand once residue sand dried down and its diffusivity fell below a critical range. Thus, for revegetation in seasonally dry climates, soil capping should combine one soil with low diffusivity and one or more soils with high total water holding capacity and high diffusivity.

Laboratory measurement of hydraulic conductivity functions of two unsaturated sandy soils during drying and wetting processes

The importance of applying unsaturated soil mechanics to geotechnical engineering design has been well understood. However, the consumption of time and the necessity for a specific laboratory testing apparatus when measuring unsaturated soil properties have limited the application of unsaturated soil mechanics theories in practice. Although methods for predicting unsaturated soil properties have been developed, the verification of these methods for a wide range of soil types is required in order to increase the confidence of practicing engineers in using these methods. In this study, a new permeameter was developed to measure the hydraulic conductivity of unsaturated soils using the steady-state method and directly measured suction (negative pore-water pressure) values. The apparatus is instrumented with two tensiometers for the direct measurement of suction during the tests. The apparatus can be used to obtain the hydraulic conductivity function of sandy soil over a low suction range (0-10 kPa). Firstly, the repeatability of the unsaturated hydraulic conductivity measurement, using the new permeameter, was verified by conducting tests on two identical sandy soil specimens and obtaining similar results. The hydraulic conductivity functions of the two sandy soils were then measured during the drying and wetting processes of the soils. A significant hysteresis was observed when the hydraulic conductivity was plotted against the suction. However, the hysteresis effects were not apparent when the conductivity was plotted against the volumetric water content. Furthermore, the measured unsaturated hydraulic conductivity functions were compared with predictions using three different predictive methods that are widely incorporated into numerical software. The results suggest that these predictive methods are capable of capturing the measured behavior with reasonable agreement.

Hydro-mechanical characterization of Barmer 1 bentonite from Rajasthan, India

The conceptual model for deep geological disposal of high level nuclear waste (HLW) is based on multiple barrier system consisting of natural and engineered barriers. Buffer/backfill material is regarded as the most important engineered barrier in HLW repositories. Due to large swelling ability, cation adsorption capacity, and low permeability bentonite is considered as suitable buffer material in HLW repositories. Japan has identified Kunigel VI bentonite, South Korea - Kyungju bentonite, China - GMZ bentonite, Belgium - FoCa clay, Sweden - MX-80 bentonite, Spain - FEBEX bentonite and Canada - Avonseal bentonite as candidate bentonite buffer for deep geological repository program. An earlier study on Indian bentonites by one of the authors suggested that bentonite from Barmer district of Rajasthan (termed Barmer 1 bentonite), India is suited for use as buffer material in deep geological repositories. However, the hydro-mechanical properties of the Barmer 1 bentonite are unavailable. This paper characterizes Barmer 1 bentonite for hydro-mechanical properties, such as, swell pressure, saturated permeability, soil water characteristic curve (SWCC) and unconfined compression strength at different dry densities. The properties of Barmer 1 bentonite were compared with bentonite buffers reported in literature and equations for designing swell pressure and saturated permeability coefficient of bentonite buffers were arrived at. (C) 2013 Elsevier B.V. All rights reserved.

Avaliação de proposições matemáticas para interpretação do comportamento de solos residuais não saturados

Nas últimas décadas, teorias têm sido formuladas para interpretar o comportamento de solos não saturados e estas têm se mostrado coerentes com resultados experimentais. Paralelamente, várias técnicas de campo e de laboratório têm sido desenvolvidas. No entanto, a determinação experimental dos parâmetros dos solos não saturados é cara, morosa, exige equipamentos especiais e técnicos experientes. Como resultado, essas teorias têm aplicação limitada a pesquisas acadêmicas e são pouco utilizados na prática da engenharia. Para superar este problema, vários pesquisadores propuseram equações para representar matematicamente o comportamento de solos não saturados. Estas proposições são baseadas em índices físicos, caracterização do solo, em ensaios convencionais ou simplesmente em ajustes de curvas. A relação entre a umidade e a sucção matricial, convencionalmente denominada curva característica de sucção do solo (SWCC) é também uma ferramenta útil na previsão do comportamento de engenharia de solos não saturados. Existem muitas equações para representar matematicamente a SWCC. Algumas são baseadas no pressuposto de que sua forma está diretamente relacionada com a distribuição dos poros e, portanto, com a granulometria. Nestas proposições, os parâmetros são calibrados pelo ajuste da curva de dados experimentais. Outros métodos supõem que a curva pode ser estimada diretamente a partir de propriedades físicas dos solos. Estas propostas são simples e conveniente para a utilização prática, mas são substancialmente incorretas, uma vez que ignoram a influência do teor de umidade, nível de tensões, estrutura do solo e mineralogia. Como resultado, a maioria tem sucesso limitado, dependendo do tipo de solo. Algumas tentativas têm sido feitas para prever a variação da resistência ao cisalhamento com relação a sucção matricial. Estes procedimentos usam, como uma ferramenta, direta ou indiretamente, a SWCC em conjunto com os parâmetros efetivos de resistência c e . Este trabalho discute a aplicabilidade de três equações para previsão da SWCC (Gardner, 1958; van Genuchten, 1980; Fredlund; Xing, 1994) para vinte e quatro amostras de solos residuais brasileiros. A adequação do uso da curva característica normalizada, proposta por Camapum de Carvalho e Leroueil (2004), também foi investigada. Os parâmetros dos modelos foram determinados por ajuste de curva, utilizando técnicas de problema inverso; dois métodos foram usados: algoritmo genético (AG) e Levenberq-Marquardt. Vários parâmetros que influênciam o comportamento da SWCC são discutidos. A relação entre a sucção matricial e resistência ao cisalhamento foi avaliada através de ajuste de curva utilizando as equações propostas por Öberg (1995); Sällfors (1997), Vanapalli et al., (1996), Vilar (2007); Futai (2002); oito resultados experimentais foram analisados. Os vários parâmetros que influênciam a forma da SWCC e a parcela não saturadas da resistência ao cisalhamento são discutidos.

砂粒含量对土壤水分蓄持能力影响模拟试验研究

通过人工配制不同质地土壤,测定土壤水分特征曲线,研究了土壤中砂粒含量对其水分蓄持能力的定量影响。结果表明:(1)砂粒含量对土壤水分蓄持能力有较大影响,土壤持水能力随砂粒含量增加递减,表征土壤持水能力的水分特征曲线Gardner模型参数及表征土壤饱和含水量的Van Genuchten模型参数均随砂粒含量增加逐渐减小。(2)砂粒含量对土壤比水容量有较大影响,试验土壤在任一吸力水平下的比水容量值均随其砂粒含量增加递减。(3)试验土壤饱和含水量与砂粒含量呈线性关系,田间持水量、凋萎系数与砂粒含量都呈开口向下抛物线右半段的关系。(4)试验土壤有效水、迟效水含量随砂粒含量增加递减,二者与砂粒含量均呈开口向下抛物线右半段的关系。易效水含量与砂粒含量呈开口向上抛物线关系。

黏粒质量分数对土壤水分蓄持能力影响的模拟试验

通过人工配制不同质地土壤,测定土壤水分特征参数,研究土壤中黏粒质量分数对其水分蓄持能力的定量影响。结果表明:1)黏粒质量分数对土壤水分蓄持能力有较大影响,土壤持水能力随黏粒质量分数增加而递增。2个水分特征曲线模型——Gardner模型及van Genuchten模型中,表征土壤持水能力的参数均随黏粒质量分数增加而增大。2)黏粒质量分数对土壤比水容量有较大影响,试验土壤在任一水吸力水平下的比水容量值均随其黏粒质量分数增大而增大。3)试验土壤饱和含水量、田间持水量分别与黏粒质量分数呈指数、对数正相关,凋萎系数与黏粒质量分数呈指数正相关。4)试验土壤有效水、迟效水含量随黏粒质量分数增加呈先升高后降低趋势,二者与黏粒质量分数均呈抛物线关系,最高点分别出现在黏粒质量分数为35.9%和35.8%处,易效水含量与黏粒质量分数相关性不显著。研究结果可为黄土区土壤水分蓄持机制进一步研究提供一定理论依据。

两种土壤水分特征曲线间接推求方法对黄土的适应性评价

土壤水分特征曲线(SWCC)是模拟土壤水分运动和溶质运移的一个重要参数,利用土壤的基本物理性质来间接推求SWCC的方法已经成为当今土壤物理学领域的研究热点。为了比较两种SWCC间接推求方法——Arya-Paris物理经验方法(简称AP方法)和Tyler-Wheatcraft分形几何方法(简称TW方法)对黄土的适应性,该文分析了黄土高原296组土壤颗粒分布、容重和水分特征曲线等资料,利用简化的Fredlund(Fred3P)模型模拟得到连续的土壤颗粒分布曲线,然后应用AP和TW方法预测出相应吸力下的土壤含水量。研究结果表明,对于黄土性土壤,AP和TW两种方法的预测结果均达到了一定的精度,相比较而言AP方法的预测效果明显优于TW方法,且受质地影响小。

土壤结构改良剂影响下的土壤水分有效性研究

以聚丙烯酰胺(PAM)与磷石膏(PG)为土壤结构改良剂,利用离心机法,测定土壤水分特征曲线,从分析土壤的吸水能力和持水能力的角度出发,研究土壤结构改良剂对土壤水分有效性的影响。研究结果表明,土壤的吸水能力、持水能力与释水能力均表现出与用量密切相关;在使用土壤结构改良剂的情况下,仍然可用van Genuchten方程很准确的模拟土壤吸力与含水率之间的关系,即可作为使用土壤结构改良剂后的土壤水分特征曲线的模拟表达式;在试验的用量范围内,土壤结构改良剂的使用不会影响植物对水分的吸收和利用。

推求土壤水分运动参数的简单入渗法──Ⅱ.实验验证

预报土壤中水分流动需要的土壤导水特性可通过观测水平土柱的入渗过程来确定，这一观测过程的分析是基于对Richards方程求积分解。土壤水分特征曲线中的参数由观测的水平立柱的特征湿润长度和吸力来确定，非饱和土壤导水率由已确定的特征曲线中的参数和测定的饱和导水率导出。供试土壤有三种，它们的质地从砂壤到粘壤。由这种方法所确定的这三种土壤的水分特征曲线与实测的特征曲线符合良好，所确定的砂壤的非他和导水率与实测值的比较令人满意。利用数值法和积分法分别计算了土壤含水量剖面，计算结果吻合良好，说明了这种方法的合理性。

推求土壤水分运动参数的简单入渗法 I.理论分析

预报非饱和土壤水分运动必须首先获得土壤水分运动参数。土壤水分运动参数包括土壤水分特征曲线和导水率。本文使用积分方法求解了一维水平非饱和土壤水分运动问题，根据其解建立了推求非饱和土壤水分运动参数的简单入渗法，用以推求ｖａｎ Ｇｅｎｕｃｈｔｅｎ特征曲线模型中的参数α和ｎ。α和ｎ是根据湿润区的特征长度、吸渗率和土壤的饱和导水率（ｋｓ）来确定的，而非饱和导水率可由α、ｎ和Ｋｓ确定。这一新的简单入渗法是基于Ｒｉｃｈａｒｄｓ方程和土壤导水特征的闭合型方程。简单入渗法提供了利用瞬态水流方法来确定土壤水分特征曲线而替代通常的平衡法。简单入渗法是一个全新的、简捷的确定土壤导水特性的方法。

Efeitos de níveis de cobertura do solo sobre a produtividade e crescimento do feijoeiro irrigado, em sistema de plantio direto

The objective of this research was to study the effects of five different treatments of grass (Brachiaria decumbens) straw mulch on common beans (Phaseolus vulgaris L.): 0% (0 t.ha-1), 25% (2,25 t.ha-1), 50% (4,5 t.ha-1), 75% (6,75 t. ha-1) and 100% (9,0 t/ha) designed by randomized blocks, with four replicates. The irrigation was applied when minimum soil water potential were reached about - 30kPa. The water management based on tensiometers and soil water characteristic curve. A microsprinkler irrigation system was used. The experiment was set up at the Experimental Station of Embrapa Rice and Bean (Empresa Brasileira de Pesquisa Agropecuária Arroz e Feijão) at Santo Antonio de Goiás, Brazil, in a Dark - Red Latosol soil. The results showed: the bean yield and his components were not affected by treatments, except grain number/pod,. The mulch increased the water use efficiency and, consequently, decreased the number of irrigations when the mulch reached more than 50% straw mulch. The treatment with 100% of mulching presented the largest leaf area index and dry matter accumulation was not affected by mulching.

Caracterización de los parámetros de resistencia al corte y erosionabilidad del suelo para su aplicación en los problemas de estabilidad de taludes en obras lineales

La tesis se organiza en un volumen de Memoria integrada por once capítulos que constituyen el cuerpo de la tesis y otro volumen de Apéndices titulado “Caracterización geotécnica de Base de los suelos de España” que reúne en forma de cuadros las características de textura, permeabilidad, humedad-succión, erosionabilidad y resistencia al corte de los cuarenta y dos perfiles de suelos representativos de los tipos del Mapa de suelos De España. Estos cuadros han sido elaborados originalmente por la doctorando durante sus estudios para la obtención del DEA de la Suficiencia Investigadora, excepto los de resistencia al corte que lo han sido también por la doctorando de forma original, pero ya en la etapa de redacción de la tesis. En el Capítulo 1 “Introducción” se describe la motivación, antecedentes, alcance y contenido de la tesis, ordenado según el índice que en él se incluye. Los Capítulos 2 “Meteorización, 3 “Balance Hídrico” y 4 “Humedades características” constituyen el “estado del arte” en el momento actual de los temas de geotecnia ambiental relacionados con la degradación de la superficie terrestre y la estabilidad de taludes. El Capítulo 2, tras matizar algunas generalidades, aporta elementos para la cuantificación de la alteración de rocas como el “índice climático de Weinert” y de la erosión de suelos como la “ecuación universal de pérdida de suelo (U.S.L.E.)” El Capítulo 3, partiendo de los fenómenos de precipitación y evapotranspiración, plantea el balance hídrico en vertientes con instrumentos para evaluar la infiltración y la escorrentía, conceptos imprescindibles para adentrarse en los de resistencia y erosionabilidad del conjunto suelo-agua. En los Apéndices A1 y A2, se recogen valores de coeficientes de infiltración en condiciones saturadas y no saturadas de los perfiles de suelos del Mapa de España. El Capítulo 4 se dedica al estudio de este conjunto suelo-agua con la definición de conceptos que lo caracterizan, basados en la relación entre los contenidos de ambos elementos o “humedad”, sus valores máximos y mínimos y la forma en la que es retenida el agua por el suelo. Este capítulo acaba con el concepto de “Curva característica Suelo-Agua/Soil Water Characteristic curve (SWCC)”, que liga el contenido de agua de un suelo con la tensión a la que está retenida (uauw) “succión” o con su expresión más usual “pF”. En el Apéndice A 3 se adjuntan las SWCC de los perfiles de suelos del Mapa de suelos de España. En el Capítulo 5 “Resistencia al corte de los suelos”, se detalla la influencia que tienen sobre la resistencia de los suelos factores como el paso del tiempo, el contenido de humedad y la presencia y tipo de vegetación en la superficie del suelo estudiado. El Capítulo 6 “Evaluación de la erosión”, analiza el factor de erosionabilidad del suelo “factor K” de la U.S.L.E., su evaluación en función de la textura, estructura y permeabilidad del suelo, con la estimación hecha para los cuarenta y dos perfiles de suelos del Mapa de España, contenida en el Apéndice 4. En el Capítulo 7 “Metodología de diseño” se hacen en su primera parte unas consideraciones geoambientales de diseño aplicables al estudio de los problemas de inestabilidades en taludes. La segunda parte constituye el núcleo de la tesis con la propuesta de “estimación de los parámetros de resistencia al corte del suelo”, consecuente con las teorías y metodología de análisis expuesta en los capítulos anteriores. En el Apéndice A 5 se presentan los valores de los parámetros coulombianos de resistencia al corte, ”c y Ф” estimados según la caracterización climática a partir del índice de Thornthwaite, en condicionesde diseño para humedades naturales máxima y mínima de los cuarenta y dos perfiles de suelos del Mapa de suelos de España. El Capítulo 8 “Aplicación a casos reales” se considera de gran interés al constituir una auténtica continuación de la segunda parte del capítulo anterior, desarrollando la metodología expuesta en él a cuatro problemáticas de infraestructuras de obras lineales, relacionadas con problemas de erosión y deslizamientos en taludes. El Capítulo 9 “Ensayos de referencia” se incluye como punto de apoyo (referencia) a las teorías expuestas, valorando la idoneidad de los tipos de ensayos y tipos de suelos seleccionados (Laboratorio de Geotecnia del CEDEX y Laboratorio Hong-Kong University of Science and Technology), utilizados para la obtención, por correlaciones deducidas, de las curvas SWCC de los perfiles de suelos del Mapa de España, incluídas en el Apéndice A 3, como se ha citado antes. En el Capítulo 10 “Conclusiones y Futuras Líneas de Investigación”se apuntan en primer lugar unas conclusiones que, a juicio de la doctorando, se pueden extraer con interés de esta tesis y a continuación se esbozan unas posibles líneas de investigación, fundamentalmente de tipo experimental, que complementarían los avances derivados de esta tesis o podrían esclarecer y abrir nuevas interpretaciones de los fenómenos naturales de erosión y estabilidad de taludes en los que ésta se ha centrado. Finalmente, en el Capítulo 11 “Bibliografía” se han reunido 328 referencias que reflejan una visión amplia y bastante completa del tema tratado, obtenida complementando las de tesis anteriores sobre esta singular materia (“Efecto estabilizador de la vegetación en taludes”, L Fort 1975 y “Determinación de las características de fricción en el contacto suelo-geotextil a diferentes succiones, mediante equipos de laboratorio singulares”, E Asanza 2009), con propias de la doctorando (9) y las consideradas de mayor interés de los últimos Congresos sobre Suelos no saturados,”Unsat 95”, “Unsat 2002” y “Unsat 2011” entre otros. ABSTRACT The thesis is organized in a volume of Memory composed of eleven chapters that make up the body of the thesis and other Appendices volume entitled "Geotechnical characterization of basis of the soils of Spain" that combines the characteristics of texture, permeability, moisture-suction, erosionability, and shear strength of forty-two profiles of soils representative of the types of the soil of Spain map in the form of pictures. These pictures have been produced originally by the student during their studies to obtain the DEA of the research, except those of the shear strength, also been done by the PhD student in an original way, but already at the stage of drafting of the thesis. Chapter 1 "Introducción" describes the motivation, background, scope and content of the thesis, ordered according to the index that is included. The Chapters: 2 "Weathering, 3 “Water Balance” and 4 “moisture characteristics" are the "State of the art" at the present time of geotechnical environmental issues related to the degradation of the Earth's surface and the slope stability. Chapter 2 after clarify some general information, provides elements for the quantification of the alteration of rocks as "Weinert climate index" and soil erosion as the "universal equation of loss of soil (U.S.L.E.)" Chapter 3, on the basis of the phenomena of precipitation and evapotranspiration, raises the water balance in sheds with instruments to evaluate infiltration and runoff, essential concepts into the resistance and erosionability water-soil joint. Values of soils coefficients of infiltration in saturated and unsaturated conditions from the Spain map of profiles are collected in the Appendices A1 and A2. Chapter 4 is dedicated to the study of this joint “soil-water”, with the definition of concepts that characterize it, based on the relationship between the contents of both elements or “moisture”, their maximum and minimum values and the way in which water is retained by the soil. This chapter ends with the concept of “Soil Water Characteristic curve (SWCC)", which linked the water content of a soil with the stress that it is retained (ua-uw) "suction" or its expression more usual "pF". The SWCC of the profiles of soils of the Spain soils Map are attached in the Appendix 3. In Chapter 5 “Soils shear strength”,is detailed the influence that they have on the resistance of soils factors such as the passage of time, the content of moisture and the presence and type of vegetation on the surface of the studied soil. Chapter 6 "Assessment of erosion", analyses the soil erodibility factor "Kfactor" of the U.S.L.E., its evaluation based on texture, structure and permeability of the soil, with the estimate for forty-two profiles of soils on the Spain Soils Map, contained in Appendix 4. Chapter 7 "Design methodology" some considerations are made in the first part geo-environmental design applicable to the study of the problems of instabilities in slopes. The second part constitutes the core of the thesis with the proposal of “estimation of parameters of shear strength”, of the soils consistent with theories and analytical methodology outlined in the previous chapters. Appendix A 5 presents the values of the coulombians parameters of shear strength, "c and Ф" according to the characterization of climate from the index of Thornthwaite, in design for natural moisture conditions maximum and minimum of forty-two profils of Spain Soils Map Chapter 8 "Application to real cases" is considered of great interest to constitute a true continuation of the second part of the previous chapter, developing the methodology exposed it to four problems of civil-works infrastructure, related to problems of erosion and landslides in slopes. Chapter 9 "Tests of reference" is included as point of support (reference) to the theories exposed, assessing the suitability of the types of tests and types of selected soils (Geotechnical laboratory of CEDEX and laboratory Hongkong University of Science and Technology), used to obtain, by deduced correlations, of curves SWCC of soils profiles on the Spain Soils Map, included in Appendix A. 3, as it was mentioned before. Chapter 10 "Conclusions and future research lines" are running first conclusions which, in the opinion of the candidate, can be extracted with interest of this thesis, and then, it outlines some possible lines of research, mainly experimental, which would complement the advances arising from this thesis or could clarify and open new interpretations of natural phenomena of erosion and slope stability in which it has focused. Finally, in Chapter 11 "Bibliography" 328 references have been included which reflect a broad and fairly comprehensive view of the subject matter, obtained complementing those of the previous theses on this singular issue ("Vegetation stabilizing effect on slopes", L Fort 1975, and "Determination of the characteristics of friction in the contact soil-geotextile to different-suctions, through special laboratory equipment", E Asanza 2009) with some of them from of the candidate (9) and the others from of the considered as the most interesting of recent conferences on unsaturated soils, "Unsat 95", "Unsat2002" and "Unsat 2011" among others.